BMW F10 3.0d Edc17cp45 possible read and write with Foxflash/KT200 via obd? or must on bench? Here’s the user test report. Hope it helps. OBD mode: Read backup bench mode, for testing via OBD VR file not download… Continue Reading
Here are some commons errors and solutions of Foxflash ecu tuning tool software. Problem: I just installed Foxflash but I haven’t received my activation code. Answer: Check the instructions, the Serial number is your code, then press Activate.… Continue Reading
Question: KT200 edc17cp14 in audi r/w ok? Bench or obd? EDC17CP14 method’s over OBD does not work. KT200 only can read but can not write this processor. Over bench mode everything is perfect. Any idea? On bench it works. Solution: Some… Continue Reading
There are many ecu programmers that can be used to read and write Visteon dcu102 dcu104 in Ford and PSA group, including KT200, Foxflash, Ktag, Dimsport, Autotuner etc. Check pinout wiring diagram to each device respectively. 1.Visteon DCU 102… Continue Reading
Possible to install and activate FoxFlash manager software on another laptop? Will it be possible to use on 2-3 computers? It would be great for us who are multiple persons in 1 company. As well for us who work outside… Continue Reading
Another Yanhua Mini ACDP tutorial: How to clone BMW MSV90 DME on bench. What’s required? Yanhua Mini ACDP host Module 27 and MSV90 interface board Old MSV90 DME new target MSV90 DME Preparation: Make connection follow instructions 1: Prepare ACDP,… Continue Reading
FoxFlash and KT200 ecu programmer support MEDC17 free tricore clone service. Most of other tools need patch the files after read out, but Foxflash is free. How to Clone MEDC17 ECUs with FoxFlash? The following functions allow you… Continue Reading
Here’s the solution to OBDSTAR X300 DP plus screen freezes boot logo flashing, non-responsive status or DiagProgram has stopped problem. Solution: Flash the x300dp plus. Download reflash boot files. How to flash obdstar x300 dp plus & other OBDSTAR… Continue Reading
KT200 and Foxflash read and write VAG Infineon MED17.5.5 successfully. ECU: MED17.5.5 Mode: Boot Mode R/W: OK Cks: Manual (there’s checksums for all ECU but some MV/ED ECUs not okay) you need to make checksum externally and car start. Search… Continue Reading
Does KT200 work with internet disconnected? Yes, KT200 now has a new dongle (offline workstation) for online. Why could need offline module? 1.It’s convenient for outdoor work. 2. To go to a client without internet. 3. Some people worry… Continue Reading
Tutorial: How to Clone Newer 2nd Generation DQ200 transmission gearbox TCM with CG FC200 programmer for Volkswagen Skoda Audi Seat. Step 1: Read Dflash, Ext_Dflash and Pflash from original DQ200 Gen2 Run FC200 software, select Audi- VAG Temic DQ200… Continue Reading
OBDSTAR X300 DP plus and x300 pro4 released new TOYOTA & LEXUS IMMO software V32.74 on Non. 24th, 2022. Supports over 90% TOYOTA/ LEXUS vehicles proximity key programming(all keys lost); Supports vehicles with gateway read smart key ECU IMMO… Continue Reading
Autel is rolling new generation MaxiIM key programmers, IM608 II, IM608S II, IM608 Pro II and IM508S. What’s the difference between MaxiIM 1st and 2nd generation? Check brief table comparison below: Item Autel IM508 Autel IM508S Autel IM608 Pro… Continue Reading
Question: I have Autel im608 and tried to code BMW on diagnostic side. It asked me for an Ethernet adapter but im608 does not have Ethernet port. Where I can order this Autel’s bmw obd and ethernet’s cables? Yes, you… Continue Reading
Where to download FoxFlash software? How to install FoxFlash? Does it require activation to use? Check Foxflash installation guide below. Operating system: Windows 7 Windows 8/8.1 Windows 10 Windows 11 Recommended Configuration: CPU > 2.5 GHz (Intel i5, i7)… Continue Reading
