OBDSTAR has rolled out the CAN Direct kit on Toyota Corolla, RAV4 , Highlander, Avalon, Lexus ES, RS and UX. With the 8A/4A kit you don’t need additional licence with OBDSTAR X300 DP Plus/X300 Pro4. Here is the 4A and… Continue Reading
We have discussed Renault CAN Clip Yes and No passthru interface before. Polish users found it also can be used with STIC SVCI J2534 passthru adapter. Here comes the free Renault CAN Clip V220 for svci VM Windows… Continue Reading
There are 2 different quality KT200/KTM200 ecu programmer boards. And they are slightly different. One has a crossover board stuck to the back of the board and the other one does not. Looks like there have been revisions between them.… Continue Reading
PSA MD1CS003 perfect work with KT200 ecu programmer. Pinout Bosch MD1CS003 TC298TP Peugeot Citroen Diesel Set up bench connection follow the wiring diagram Read data very fast Writing flash Checksum correction ok KT200 Write flash successfully
Question: How can I use FCA SGW on Autel MaxiIM IM608, IM608 Pro or IM508? Is it possible to have a SGW subscription? I have 12+8 cable but I don’t want to spend time searching for sgw location. I want to use fca authentication… Continue Reading
Latest 07/2022 GM GDS2 Global Diagnostic System software has been tested and verified working with GM MDI and MDI2 multiple diagnostic interface. GM GDS 2 -Latest Update 2022.7 – Unlimited Lease – Works with MDI or MDI2 –… Continue Reading
Yanhua Mini ACDP tech released new module 28 to clone ZF-9HP gearbox in boot mode. Supports Jaguar, Land rover, Chrysler, Dodge, Fiat, Honda, Jeep and other models of the ZF-9HP gearbox boot mode cloning. Module features: 1. The interface board… Continue Reading
Free Download GM GDS2 Global Diagnostic System 2022.05 & 2022.07 software. V2022.05 GM GDS2 Date: May 2022 Version: V2022.05 Operating system: Windows 7- Windows 10 (32 bit) native install Device affected: vxdiag vcx nano gm/opel wifi/usb device… Continue Reading
In some cases, we need to reflash the Autel MaxiIM KM100 firmware. For example, if your device automatically restarts every 5-10 minutes. Download KM100 flash files https://we.tl/t-gzlwQ6YhHI Preparation: One TF card (larger than 4G, please backup all personal files)… Continue Reading
Both Fetrotech tool and ECU Bench Tool are the clone of AMT BST bench tool. Which one is better? Part I Check the table comparison below: Item Fetrotech Tool ECU Bench Tool Image Software version Fetrotech 1.2.7 AMT Bench… Continue Reading
There are not many tools to make PSA group DCM6.2A ECU via OBD. KT200/KTM200/ECUTuner ecu programmer is confirmed working via OBD. Reading writing flash by OBD DCM 6.2A PSA SUCCESS: i.e Peugeot 308 2.0 BlueHDI Read flash in 1m… Continue Reading
Here is another Fetrotech Tool software Windows 10 Pro system installation instruction shared by Stephane Matyjasik. Here is the solution : Desactiver windows defender, smartscreen etc… Go in settings bar > Administration tools > Computer management > Local users and groups >… Continue Reading
Problem: The ecu bench tool device has stopped communicating with the ECU. S1 error s2 pinout error. edc17 doesn’t connect either. I connect it well. Solution: Make sure the driver has been installed and the wiring connection is correct. Don’t… Continue Reading
Some users reported that they cannot find MB SD Connect C4 DoIP WLAN connection (No WLAN) in SDConnect Toolkit. No possible to set up WiFi connection? NO WLAN does not mean wifi cannot be used. For MB SD C4… Continue Reading
Fetrotech tool requires a modern laptop and strictly follow the instruction to install/ activate the software. if cannot open fetrotech, task bar will disappear after the splash screen. Here is an easy solution to fix it without reinstalling the operating… Continue Reading
