Best BMW fuel injectors coding tools: Inpa, Foxwell nt530, Autel MX808. This article will be available with the operation procedure one by one. 1.Code BMW fuel injectors with INPA 2.Code BMW fuel injectors with Foxwell nt530 3. Code BMW… Continue Reading
Car model and year: a 2003 E85 with an M54 engine Purpose: Looking for Good fault reader/analyzer Reviews: I have Creator 310 for BMW, works for me. I have a 2.5 ,2003, Z4. Has helped me diagnose and… Continue Reading
Car model and year: 2011 BMW Z4 E89 Problem and BMW scanner to use: the rear axis sensor is very near its low limit. Therefore my headlights are not raising to the proper operating height. When I start the… Continue Reading
This is for those are researching what he should buy for his BMW. The option is narrowed on BMW ICOM cable + Rheingold and Carly Pro for BMW + Carly gen2 adapter. Carly can run diagnostics and code. It… Continue Reading
I have a number of interfaces: – CarSoft – VAG COM – INPA with serial port – K+D CAN with USB (opaque colour casing) – ADS/OBD interface My current favourite is the K+D CAN USB. It works on all current… Continue Reading
Here, you will get answers to questions below: It is possible to use an “old” vcds or vagcom kkl cabel and use it for newer bmw (2004-2011) with the software inpa? Only short the Pin 7&8 from my vcds cable,… Continue Reading
This is a great write-up of INPA BMW software and hardware (K+DCAN interface), incl.: Part 1: INPA software – inpa bmw definition – inpa 5.0.2 & 5.0.6 download – inpa software install (windows XP/7/8/10) – inpa driver software installation… Continue Reading
Problem: I’ve done 1x CAS2 with CGDI BMW – 2006 E90 Diesel ELV sync was OK CAS sync failed, ERROR and would not start car did not start until i used another tool to do the CAS sync. … Continue Reading
The BMW Coding Tool 2.50 allows you to update your SP-DATEN (Data files) automatically instead of manually installing the files by copy and pasting files. It will automatically update the files that require replacing and skip the files that you… Continue Reading
Here are the details of my setup of MacBook Pro with VW Fusion – Windows 10 or Bootcamp, both working for BMW coding with ICOM software. Hardware: 2015 Retina Macbook Pro 16GB RAM, 512GB SSD Software: VMWare Fusion 10… Continue Reading
Here’s little tutorial on BMW E-series coding programs installation. Disclaimer: The document was translated from Korean. You are at your risk. Part I. Required files 1. INPA 2. BMW Coding Pack 3. BMW Coding Tool → Download E_coding.zip Unpack and… Continue Reading
When I go to work today, I open my laptop and connect BMW K+Dcan cable to my car, but I get an error when I try to read another module other than CAS of ECU module… I have a problem with the ncs… Continue Reading
This post will show you how to easily find the ZB number when flashing an E -series module. Programs: The programs used for Ecu Flashing are Winkfp (E-series), E-sys (F-series) and ISTA-P (ALL). Definition of Flashing: Flashing an… Continue Reading
What is K+DCAN cable with switch: It’s a BMW K+Dcan usb cable, the 2018 version. In detail… Look here: A new switch is added, compared to the traditional Dcan cable. the switch on this cable to LEFT is for… Continue Reading
Have spent my entire Saturday on this: All running on XP and also tried on Win7 x64 INPA is working fine. Battery and ignition both ON When running NCS Expert, try to read the VIN from ECU i get VIN… Continue Reading
