Problem: One of the Magic Motorsport Flex users was trying to read the Peugeot 508 Delphi DCM6.2A ECU via OBD but failed. It reported an error: Requires time delay not expired. Safe by obd mode or go for boot mode?… Continue Reading
With Magic Motorsport Flex version 8.31.0.0, Bosch MD1CP007, MD1CP017, and MG1CS028 ECUs used in Jaguar and Land Rover vehicles can now also be unlocked with Korhex. Previously supported through Voltage Fault Injection (VFI) technology, these ECUs can also be managed… Continue Reading
Problem: Tried to connect Mercedes Benz CPC5 ECU with OBDSTAR ECU Master C pack as it appeared. But ECU Master failed to read this ECU. It gave this message: ECU is locked. Use the corresponding (LOCKED) path to proceed. Any… Continue Reading
Problem: Magic Motorsport Flex unlocked Jeep Grand Cherokee WL 2021 GPEC5 ECU in boot mode successfully. Install ECU back into the vehicle. Flex is unable to connect to it via OBD. The vehicle starts and diagnostics work normally. Do I… Continue Reading
Problem: Tried to read the 2024 Hyundai Sportage Kefico SIM2K-510 ECU using Flex programmer by OBD. Flex software says SGW detected and failed to connect via OBD. No communication on bench (ERROR). Any solution? Solution: This model uses CAN FD communication… Continue Reading
SIM2K-510 New Exclusive Solution is coming!! New protocol released in Magic Motorsport Flex software version 8.28.0.0 allowing technicians to program Kefico SIM2K-510 units in OBD, following a simple, fast, and more efficient procedure. Connect, read, modify! Just connect the OBD… Continue Reading
Problem: Tried to boot glitch unlock a VAG MD1CS004 H80 ECU with Korhex. Flex reads ECU ID, but nothing happens. Flex software is stuck on the glitch progress page. Any solution? Solution: Sometime you need to move korhex. Move Korhex… Continue Reading
Does Magic Motorsport Korhex require activation? Yes, Korhex requires activation. How to activate Korhex? The activation process is straightforward and follows these steps: Open the Magic Motorsport Flex software and click on “Help Desk” to go to the Magic Motorsport… Continue Reading
Flex +Korhex now supports unlocking the locked Bosch MD1CS069 ECU found in the Fiat Ducato. We’ve put together a fresh review of reading and writing the 2023 Ducato Bosch MD1CS069. “FIAT DUCATO 2023 – BOSCH MD1CS069 | KORHEX SUCCESS! Another… Continue Reading
Problem: One of the Flex users had a problem connecting Korhex adapter for unlocking ECU. Software shows Connected. But the RGB LED near the USB/power connector keeps flashing red continuously. Solution: The flashing red LED does not necessarily mean there… Continue Reading
Flex Korhex released new protocols for Industrial and Commercial vehicles. Flex version 8.26.0.0 is now available Unlock Bosch MD1CS069 and MD1CS089 ECUs without working on the PCB. Flex version 8.26.0.0 expands Korhex support to Bosch MD1CS069 and MD1CS089 ECUs installed… Continue Reading
Will Magic Motorsport Flex clone PSA Bosch EDC17C60 ECU 1:1??? It has OTP zone. Not 1: 1 clone*. Some users deactivate OTP zone and clone ECU on bench 1: 1. You will change the password and will never write again… Continue Reading
MMS Flex Korhex DAF Delphi ETC3 UDS locked ECU unlocking review: With the new Flex + Korhex solution, ETC3 UDS units can now be unlocked and programmed directly in our workshop, eliminating the need to ship the control unit elsewhere.… Continue Reading
MMS Flex+ Korhex boot glitch unlocking new user report: Tested Korhex today; all worked as expected. Mercedes Benz 2022 Bosch MD1CP001 ECU locked. No welding. No dangerous openings. No more sending it away for the unlocking. With the new Korhex… Continue Reading
Problem: An MMS Flex user was trying to read an EMS3161 from a Dacia, and flex Connect ok, but the only button available is recovery. EMS3161 protocol exists but does not read. Do it with Autotuner. Some users reported that… Continue Reading
