Now Magic Motorsport Flex programmer is possible to unlock VAG Bosch MD1CS004 H80 ECU. Here comes the latest user report: Seat Leon 2.0TDI 2024 With Bosch MD1cs004 HW80 ECU. Unlock successfully with Flex. GLITCHMODE 10 second Connect. Read and Write… Continue Reading
Great News! Magic Motorsport Flex programmer update Bosch MDG1 ECU boot unlocking without RFT (mail-in unlocking). Bosch MDG1 No RFT Version 8.0.0.0 of Flex Out Now As of today, you can unlock and program Bosch MDG1 control units directly in… Continue Reading
New Magic MotorSport Flex Update: GPEC5 Boot Unlock without RFT! You can now unlock Continental GPEC5 ECUs of Jeep and RAM vehicles directly from your workshop—no ECU shipping and no RFT service required. Version 7.60.0.0 of Flex out now to unlock GPEC5 Stellantis… Continue Reading
No unlock. No Bench. Just OBD. With Magic MotorSport Flex version 7.59.0.0, working on Continental SID212 and SID212EVO ECUs installed on Ford vehicles becomes even faster and more efficient. The new protocol gives you direct access to the map area… Continue Reading
Could Magic Motorsport Flex clone Peugeot Delphi DCM7.1B ECU? Or should I make immo off on the donor ecu? Yes, you can 1:1 clone in boot mode. Boot read and write, job done. Immo off also available. It is a… Continue Reading
Problem: Magic Motorsport Flex programmer reads Peugeot 307 SID807EVO ECU ok, but cannot write the modified file by OBD. It is a keyless system. Error authorization from ECU failed. Solution: The keyless ones have to see the key in the… Continue Reading
Problem: After writing the Renault SID321 ECU with Flex programmer via OBD, the car does not start. After writing obd, the connection was lost. Then tried it with the bench. No luck. The ECU now has no communication. Any solution?… Continue Reading
Magic Motorsport Flex 7.54.0.0 just dropped and brought RFT (Ready For Tuning) for VAG 2.0 TDI (2022-2024) locked Bosch MD1CS004 ECU. The new Flex update 7.54.0.0 has just been released, allowing you to manage the unlocking of protected ECUs installed… Continue Reading
Magic Motorsport Flex programmer update just dropped. Bench support now added for: DQ500 Gen2 DQ38x (2022+) ZF AL552 Gen2 (2022+) With the release of version 7.52.0.0, Flex introduces Bench mode for Bosch DQ500 Gen2 TCUs, which are increasingly widespread on… Continue Reading
Is it possible to clone 2019 Ford Transit SID211 ecu with the Autotuner tool? Is it a straight clone on bench 1 to 1 without opening? No, You must transfer password, not possible bench clone 1 to 1. Needs password… Continue Reading
Problem: Trying to unlock a Ford SID212 ECU with Magic Motorsport Flex programmer and it’s saying ‘No virtual read available for this sw version. Cannot download files from server’ anyone had this issue? Solution: No VR file on the server.… Continue Reading
New Magic Motorsport Flex software update available – v7.50.0.0. Bench protocol now available for Continental SID212 and SID212EVO! From today, the RFT service is no longer required. With Flex you can now unlock and program these ECUs directly in Bench… Continue Reading
Question: There is no protocol for Ford Transit Visteon DCU-101 in Flex software. Will Flex Read Visteon Dcu 101? Is it safe to use dcu-102 protocol? Here is the clue. Yes it can do through protocol for DCU102. Ford… Continue Reading
Magic Motorsport Flex and Autotuner programmers now support the Bosch MD1CS069 ECU OBD protocol for the Iveco Daily. MMS Flex New Flex update, version 7.49.0.0, now available, implementing OBD programming for the most modern Iveco vehicles equipped with… Continue Reading
Problem: 2011 BMW X6M all keys lost. Already read the CAS3+ and saved eeprom dump. DME is an MSD85.3. Which tool will get the ISN code from DME? Autel IM608: Failed Bench failed with a Gbox2/3. Double checked sufficient… Continue Reading
