VNCI RNM and Openport 2.0/Godiag J2534 which is a better inexpensive VCI that can be used for diagnosis and programming with Renault CAN CLIP or ADT software? Renault CLIP: Both VNCI RNM and Openport work with Renault CLIP software. Tactrix… Continue Reading
We have pointed out how to configure J2534 passthru devices (Godiag j2534, 5054a, PCMTuner, SM2 pro) for Nissan Consult III Plus software. How to Configure Nissan Consult III+ with Passthru Devices? Here we show how to set up Tactrix Openport … Continue Reading
As titled, what is a better Techstream cable for K-line Toyota models? Here is the clue. 1.Mini VCI cable Firmware 1.4.1: The latest 1.4.1 firmware interfaces have both CAN chip (xx1050) and K-Line chip. so they may full… Continue Reading
Problem: Downloaded Xentry passthru version for the Openport 2.0 interface (Openshell version does not run) or other passthru device (vxdiag vcx se benz etc). Once installed, the capacity is quite large. Download capacity is 19GB Has some problems during installation: When… Continue Reading
Long story short, I’ve found out that Tactrix has RS232 input which can be used very easily to add any amount of external sensor, eg: oil pressure, fuel pressure, O2 sensor, Knock sensor, WMI flow sensor, etc. This won’t be… Continue Reading
Openport 2.0 and godiag GD101 J2534 which is a better J2534 passthru device? Let’s take a look at the comparison table first. Item Openport 2.0 Godiag J2534/VNCI NANO J2534 Protocols CAN 2.0 CAN/ISO15765 and K-line KWP2000/dual K-line ISO15765, ISO9141,… Continue Reading
It is possible to use Renault CLIP software via Openport 2.0 passthru interface. You need to trick Clip into believing your passthru (j2534) vci is an Alliance VI probe. How to configure openport 2.0 with Renault Clip? 1.… Continue Reading
Here are tips to configure Nissan Consult software for J2534 Passthru devices (vas5054a, openport, vxdiag, pcmtuner, sm2 pro, godiag j2534, jbox2 etc). Here comes a free Nissan Consult iii+ V75.15 software. Free to test with j2534 devices. VAS… Continue Reading
How to Set up Subaru SSM4 (Subaru Select Monitor IV) software with J2534 Device? You can make SSM4 work with any J2534 capable device. SSM4 is compatible with most SAE J2534 interfaces such as Autel Jbox, Snap-On passthru… Continue Reading
Which is better Mercedes Benz MB Star diagnostic device? VXDIAG, MB SD C4 or OpenPort2 VCI? Openport 2.0: The disadvantage of the connector is it falls of with constant use. We recommend openport with a gold connector. There is a… Continue Reading
Tutorial: How to activate the HBA (high beam assistant) function on Subaru using Openport 2.0 passthru and SSM4 (Subaru Select Monitor IV) software. I got an Openport 2.0 full chip adapter from obdii365.com to try and poke around potential… Continue Reading
This is a contribition on how to enable/activate the automatic transmission Agility (A) and Manual (M) Modes on Mercedes W211, W212, W204, W207 X204 7G Gearbox 722.9xx and 722.6xx series using Vediamo The fact is that the control unit… Continue Reading
You cannot use Vediamo 5 with Tactrix openport 2.0 because 5 does not support passthru so you need to install Vediamo 4 with openport (Check Openport Xentry Pros & Cons). Here are the tips on installing and configuring Vediamo with… Continue Reading
Mini VCI and Tactrix Openport 2.0 which is a better j2534 interface for Toyota Techstream software? MINI VCI: A lot of users have been using the mini-vc1 j2534 cable and it works fine with techstream. It is compatible with… Continue Reading
Is it possible to use Renault can clip via Passthru interface? Which device passthru do you recommend? Whats modifaction we have to do? Yes, it is possible. You need to trick Clip into believing your passthru (j2534) vci is an… Continue Reading
