Acdelco tds (GM Chevrolet online programming) work perfectly with PCM Tuner. Using pcm as passthru j2534 interface. For example: Programming new ABS module on a Chevrolet Express 2WD 2013 van You pay $45 per Vin good for 2 years on… Continue Reading
Question 1: Someone has an adapter for reading GM ACDelco ecus with Launch X431 X-prog3? Question 2: Launch has the wiring diagram to a part that’s not included with the xprog3. Where can i get the adapter for xprog3 mcu3?… Continue Reading
KT200 full or Foxflash read and write Fiat MARELLI 9DF via both OBD and bench mode. HW000, no need to Open, 25min read (with eeprom), 10min write. HW001 if not Open 2.5/3h read, you have to open and JTAG… Continue Reading
There are three ways to read BMW MSV80 MSV90 MSD85 MSD81 MSD80 etc DME ISN with Yanhua Mini ACDP, Open DME shell to read ISN OBD/CAN mode Bench mode Way 1: Open DME shell to read ISN The… Continue Reading
Here is the customer DIY solution for those who bricked their mini vci j2534 interface after using Firmware update tool. SOLUTION: STEP 1: Download the hex file attached. STEP 2: Download Flash Magic (used version 13.20) STEP 3: Connect the… Continue Reading
New test feedback: Renault Premium truck 420 dCi common rail engine with ecu Bosch MS6.3 read and write OK with KT200 full ecu programmer. Select Driver : Truck OBD – Renault MS6.3 Search pinout under manual Renault diesel Bosch MS6.3… Continue Reading
VNCI NANO (Vehicle Network Communication Interface) or the Godiag j2534 (black color, they are the same) is compatible with J2534 Passthru (HDS, TIS, ODIS, VIDA, PCMFlash etc) and ELM327 software (ELMConfig, Forscan, ScanMaster etc) Obdii365.com technician has tested 6 software… Continue Reading
Symptoms: It is a common phenomenon that Mercedes Benz Vito/Viano, W636/W639 doesn’t show mileage at all after replacing second-hand instrument cluster. Cluster (new type ) Eeprom: 25LC640 (25640) Solution: Disassemble the instrument cluster, remove dashboard, locate chip IC 25LC640, read… Continue Reading
One of our customers use Lonsdor K518ISE to add a new key to a 2008 BMW CAS3++ ISTAP. Had battery stabilizer on 13.7 entire time and good internet. Original key and new key not starting car. New key buttons are working. Error… Continue Reading
Ford Transit SID211 Full flash read/Write with foxflash or KT200 via OBD, only full flash possible OBD, EEPROM+Flash needs BDM. If you prefer to have a spare eeprom if anything went wrong, make a backup by boot mode, then write… Continue Reading
I have encountered real trouble many times but I haven’t found proper information online. I did today a key for a Kia Forte 2018. It is an 80bit chip, so there is not a lot of information out there for… Continue Reading
There is the Launch X431 Euro Pro5 which costs almost 3500 euro and another X431 Pro5 which is less than half the price 1500 euro. What is the difference between the two? The cheap one is a clone of the… Continue Reading
Q: KT200 full cannot read ID and flash on Mercedes Temic PLD ECU. Mine is 2018 year, same with EU5. Power use Battery 12+ power supply. Any solution? Solution: Only 24V, 12v won’t read/write. YOU must have extra switch (from… Continue Reading
KT200 ecu programmer is the least expensive flasher to read Simos 18 ECU. How to Read Simos 18 ECU with KT200? Below is the procedure to read the password (Step 1) and to set the control unit in the… Continue Reading
Hw to read John Deere Phoenix L12 ECU? KT200 ecu programmer will read Phoenix L12 Ecu successfully, fast reading on bench. PINOUT PHOENIX L12 JOHN DEERE DIESEL KT200 Read ID ok Read both flash and eeprom no problem… Continue Reading
