This is for those who are looking for a new Fgtech 4 firmware 0475, released in the year 2019. The reasons why you should have 2019 Fgtech 4 fw 0475 instead of the old fw 0386: 1: Components improvement… Continue Reading
Here is the detail guide to install Fgtech Galletto 4 V54 master ecu programmer software driver on Windows XP, Windows 7, Windows 8, Windows 8.1 and Windows 10 respectively. Part 1.Operation System Requirements Part 2. Install FGTech EOBD2 Software… Continue Reading
Look here: how to connect Fgtech galletto v54 master with a Marelli ECU on Fiat Marelli MJD 8F2 8DF 8DS – MPC5565 – FIAT DIESEL Marelli MULTIAIR 8GMF.A5 – MPC5565 – FIAT BENZINA Marelli MULTIAIR 8GMF.01 – SPC5553 –… Continue Reading
The ECU is built on the Infineon Tricore TC1766 processor. In the chip of the processor is a flash memory in volume of 1504 bytes and EEPROM in 32 bytes. There are two ways to read-write a block: via the… Continue Reading
Here are solutions to unlock this ECU: Astra H 2.0 Bosch Me7.6.2. Q: Hello can tell me any good tool for reading opel ecu for chip tuning. Bosch ME.7.6.2 – Z16LET – Z14XEP Astra H and Corsa. Option… Continue Reading
About: Simos PCR2.1 full flash There are several parts included: What is Simos PCR2.1? What tool can read/write PCR2.1? How to full read/write PCR2.1? Which better for PCR2.1 read/write? What is PCR2.1? What tool can read/write… Continue Reading
It’s possible to make full read of Mercedes ML w166 edc17cp46 with Ktag master clone and trasdata software? Yes,work 100% ECU: Mercedes ML w166 bosch edc17cp46 Both Fgtech Galletto v54 clone and Ktag OK for Mercedes edc17cp46? read and… Continue Reading
Fgtech Galletto 4 V54 Windows 7 has been tested to work perfect. But for some users, there are some troubles after Galletto v54 installation, e.g. Galletto 4 v54 won’t start/run after install. Here is the how-to’s and FAQs of Fgtech V54 Windows… Continue Reading
This is FGtech Galletto 4 v54 PCB design and component position from EU to China. Galletto V54 EU clone: Eu pcb its Gold immersion and not hot air surface level like China. You can change a lot of parts… Continue Reading
This is a thread- “100% tested /worked bench unlock and flashing (read and write ) on pcr2.1”, posted in digital-kaos.co.uk. Good information, so i share this thread again. No one but yourself should take responsibility of what you… Continue Reading
Which tool is the best solutions for Opel EDC16C9 write? Some with mppps, some with kess v2, galletto fgtech v54… Here, I collected all useful info for you to write EDC16C9. Mpps cable is verified to write EDC16C9 perfectly!!!!!!!… Continue Reading
Here is the customer final solution for the Fgtech Galletto 4 V54 master ecu tuning kit installation with windows 7 Install FGTech Galletto V54 correctly with Windows 7 Hello, I would like to explain to you step by step how… Continue Reading
How to choose the right ECU tuning tool you need really? MPPS v18, ktag, kess, fgtech4 or 2? Tips from pros here… Hope this helps. ECU tools/ Communication MPPS V18 KESS v2 KTAG FgTech galletto v54 OBD2 √ √… Continue Reading
Here are two optional solutions of how to read Iveco EDC7UC31 Bosch ECU by using FGTech galletto and Ktag ksuite v2.10 respectively. This is the Iveco truck ECU Bosch EDC7UC31 to read: Solution 1: Ktag v2.10 read EDC7UC31… Continue Reading
Have tried to flash EDC16 with KESS V2 clone, but i can not see anymore HW and VIN from the EDC16 ECU and the car not starts! Then worked with Fgtech Galletto v54 master, all EDC 16 on BDM without… Continue Reading
