Yanhua Mini ACDP is not only a key programmer but also an eeprom programmer based on mobile system. Here’s the demo guide to read eeprom and change odometer on a Hyundai Verna. No need laptop No need to remove… Continue Reading
Here’s the working solution to wiTech Micropod 2 clone Chrysler diagnostic tool registration problem. Error: “Registration is needed Device with serial number*** is not registered. Please check the knowledge base to determine how to register a device” Obdii365.com engineer solution: Right click wiTech… Continue Reading
Here’s the instructions for operating BMW EDIABAS software applications under use the ENET cable Ethernet connection. Version 1.01 Connection EDIABAS and ZGW: Hardware requirements: – EthernetCard (RT45) – ZGW (Central Gateway) – Patch cable (standard network cable with 1:… Continue Reading
KEYDIY KD-X2 transponder and remote maker Notice on June 5th, 2018: After verification can calculate the 96 bit 48 copy function. Both android and iOS system works now. Please use kd-coins to have a try. One time calculate need 150… Continue Reading
What’s KTMFlash? The KTMFlash is a ECU Programmer & transmission power upgrade tool which can read the chip data, change the engine computer, read transmission data etc at a high speed. KTMflash Functions: 1.Read the car ecu via OBD. 3.Read the BOOT mode… Continue Reading
I took some time to do a little review of these BDM connectors (China) for Ktag 2.23. I have already received the shipment and I have time to test them without problems in Bosch EDC16U1 and in bosch EDC17c46. before using them… Continue Reading
Today, We’ll show you how to learn LED status to check if your wiTech Micropod 2 Chrysler Dodge Jeep diagnostic interface works good or not. Tech support from obdii365.com wiTech Micropod II LED behavior… Here you go. … Continue Reading
Today I received the tool Lonsdor K518ISE (mainly because of CAS OBD functions… As till this day, there were many positive opinions) and I hope it will not make surprises like that, especially in 1st use… If I get BMW CAS I… Continue Reading
For the way that I’m going to be using the Obdstar X300 DP pad, it’s fine with it. As for why Focus is going with the pad X300 DP, instead of using Digiprog 3 or other odometer correction tool,… Continue Reading
Lots of things you’d better know for OBD ID48 and 96bit 48 copy with Xhorse tools incl VVDI2 and VVDI Key Tool. OBD ID48 and 96bit 48 copy: ID48 96bit Car List: Model ID Year Skoda Octavia 48 Up to 2017-18… Continue Reading
How to: change replace the BMW CAS3 MSD80 DME Engine Computer using CGDI Prog BMW key programmer. When is required: A secondhand/used DME (MSD80) was to used to replace the original DME (MSD80) Model example: BMW E83 CAS3 DME MSV80 Procedure:… Continue Reading
Here are questions and answers of AURO OtoSys IM600 key programming tool, which helps you out. Look here: Q: Is this IM600 any good? Pros and cons? A: For diagnosis and programming of some modules this is perfect Works… Continue Reading
CGDI Prog BMW is not only able to program keys, read ISN code, but also do ECU coding and programming. Here’s the factory guide to code/program F-series module, i.e FEM Body as an example. CGDI BMW FEM Body Coding:… Continue Reading
Here’s the tutorial on BMW FEM/BDC key programming (add key & all keys lost) by using CGDI Prog BMW key programmer. 1.Read and Backup eeprom 2.Add a key (copy key with key) 3. Program all keys lost (copy key… Continue Reading
How to: clear & synchronize BMW CAS with EGS using CGDI Prog BMW MSV80 key programmer. Note: To have CGDI BMW EGS authorization, you should have at least one another CGDI programmer, i.e CG100, CG Pro 9S12, CGDI MB etc. Then… Continue Reading
