Problem: Just purchased an OBDstar iScan Ducati scan tool off obdii365. My intent was to use it to clear the service code on a 2009 Hypermotard S. But I can’t get it to work properly. I know there are dozens of pages on… Continue Reading
Here comes a similar problem: “I read this GM ACDelco E98 ECU with foxflash tool by OBD and modified the original file. When writing the modified file (OBD altered file) and for some reason it got it wrong halfway… Stopped… Continue Reading
Here are the instructions for importing/exporting/transferring data file from OBDSTAR DC706 tablet to PC. Same procedure goes to OBDSTAR P50. Way 1: Use U Disk Insert a USB Disk into the USB port of the DC706 tablet. Go to… Continue Reading
The solution here is intended to solve the Launch X431 Bluetooth VCI connection problems. 1. Bluetooth connection failed 2. Firmware update failed The solution can be applied to all Launch X431 tablets with DBScar (V, VII) VCI connector, including X431… Continue Reading
What’s the Difference between Autel MaxiIM IM608 II (IM608 Pro II) and OTOFIX IM2 universal key programmers? Table 1: IM608 II vs OTOFIX IM2 Item Autel IM608 II/IM608 Pro II OTOFIX IM2 Brand Autel OtoFix IP limitation No No… Continue Reading
How to read and write ECU MD1CS006 from Renault Trafic 2.0 2021 with FoxFlash tool on bench? ECU location Read ok Write ok Checksum by foxflash. To read and write use the following driver: → BENCH MODE → RENAULT… Continue Reading
Here comes a similar problem: One of our customers failed to reset oil on a Jeep Renegade 2020 with Autel MaxiCOM MK908 II diagnostic scanner. Error message “Unlock failed. The tool did not allow.” Solution: For 2018+ FCA Chrysler Jeep… Continue Reading
How-to: read vehicle battery capacity using cheap Autel MaxiAP AP200 obd2 scanner. Not our work. Contribute to MrFixit from insideevsforum. You are at your risk. Background One of the most important, expensive, and worrisome components of any electric… Continue Reading
What’s the difference between Thinkcar Thinkdiag and 2023 new Thinkdiag2 obd2 scanner? Here is a table comparison: Thinkdiag Thinkdiag 2 Bluetooth Yes Yes, Bluetooth 5.0 Software All software activated All software activated App Thinkdiag App Thinkdiag 2 App Indicators… Continue Reading
Can Autel MaxiAP AP200 and Xtool Anyscan A30M obd2 code scanner program keys? Which is better? Autel AP200: This Autel scanner represents a cheap all system scantool for DIY and is one of the best professional budget scan tool… Continue Reading
Foxflash tool released Engine fault code shutdown update on October 03, 2023. Engine fault code shutdown update series October 03, 2023 Modern electronic engine failure achieves sensor unrepairable failure recovery by turning off the fault code. We are… Continue Reading
Volvo DELPHI CEM 2015- R5F64525 cloning was successfully done by OBDSTAR DC706. Model example: Volvo XC70 CEM 2016- Part number: 31412971 AA Chip type: R5F64525 In DC706, search Volvo CEM Delphi 2015- R5F64525 (bench) Check wiring diagram Connect CEM… Continue Reading
Problem: Foxflash failed to read Audi A1 1.4tfsi ECU MED17.5.5 on bench. error bench not not supported. Possible reason: It read fails due to security tprot hence this ECU has dealer security update so cannot be read on bench. … Continue Reading
A customer failed to read Opel Siemens SIMTEC71.6 ECU with foxflash programmer, software gave an error silent key. Foxflash engineer solution: Regular bench mode may fail to read this ECU. You need a breakout box converter, i.e Godiag GT105 to… Continue Reading
Question: How to read and write JCB Delphi DCM3.3 ECU? I have MagPro2 x17 master; Flex Master; Ktag 2.23 ; Kess 2.47 ; No clue about it. Read/Write is it ok? Obd? Bench? Boot? Solution: Kess V2: Not read… Continue Reading
