With the CAN Direct kit you are able to program latest Toyota 8A/4A smart key (add key and all keys lost) with obdstar x300 dp plus without a passcode. Here we successfully generate a simulator key of 2021 Toyota RAV4… Continue Reading
What’s the difference between KT200 and Foxflash ECU TCU chip tuning tool? Which is better? First of all, check a table comparison below: FoxFlash KT200 from ECUHelp Image Full Full version only Auto version Full version Master or Slave… Continue Reading
A few people reported an issue with PSA EDC16C3 with KT200 on bench mode. No way to read this ecu by bench. They tried to connect to an EDC16C3 ECU and, an isntant after I click on “connect” button, the… Continue Reading
You are able to reset BMW FEM/BDC mileage with VVDI2/VVDI BIMTool, CGDI, and Yanhua Mini ACDP. ACDP Mini is easier comparing CGDI and VVDI. Here is the instruction to reset BMW FEM/BDC mileage with Yanhua ACDP. NOTE: Only resets… Continue Reading
Ford SID206 is similar architecture ecu as SID208. KT200 ecu programmer can read them fine via both OBD and BDM mode. 1.SID206 OBD Mode: obd okay read, write. Ford kuga 2.0tdci 136km sid206 Read and write obd okey. Checksum… Continue Reading
This is a pretty long true unbiased review of Xtool D8 and Launch X431 V+ pro. Hope it helps you make a better decision about which one should you get. Received the Xtool D8-BT obd2 diagnostic tool today. I… Continue Reading
Thinkdiag, Carly and Torque pro scanner which is better? What’s the bad and good? Check the advantages and disadvantages of each obd2 scanner below. Thinkdiag App: The ThinkDiag from ThinkCar is full bidirectional; it can do most of the… Continue Reading
Lonsdor released Hyundai and Kia 8A smart key programming using PS6000B and PA7800B smart keys. Here is the Hyundai Kia 8A smart keys supported vehicle list and shell. Software and Frequency are convertible. Supports P4 versions: 0000A3A3 / 000000D3 / 0000D3D3 0000B3B3… Continue Reading
Xtool tech released 2019+ Toyota 8A/4A Smart Key Programming (Via key emulation & generation) function on Oct. 2022. Check Instruction below. Tools you need Xtool tablets (X100 pad3, x100 pad elite, D8, D8 BT, D9, D9 Pro, A80/H6 pro etc)… Continue Reading
Possible to make Fetrotech tool silver version work alone without pcmtuner? Yes, it is possible. Some users have managed to make it work alone. The Fetrotech tool silver works with pcmtuner because PCMtuner has a bridge at this point. It works on the… Continue Reading
Some people have problems reading EDC17 with OTP protected. For example Corsa D EDC17C18, OTP protected and KT200 ecu programmer not write other file. EDC17 OTP ERROR solution:- think due to try to write FULL flash not partial. Please read… Continue Reading
FCA Mitsubishi Bosch EDC17CP52 users’ working experience: KT200 manual does not specify to use capacitor Tried without cap could not get to connect till add cap 10uf/25V and successfully enters programming read/write/checksum. if you look in your KT200 Kit supplied,… Continue Reading
Has anyone tried Autel MaxiIM IM608 key cloning (all keys lost) on 2018, 2019, 2020 Land rovers? What does the new 2015+ land rover update do saw something about cloning key. Is that like the londsor and avdi? Yes, people… Continue Reading
Autoauth is what Chrysler uses for user authentication for 2018+ SGW vehicles. FCA Chrysler doesn’t allow a tool into their secure gateway unless it’s registered with AutoAuth. For US Chrysler Fiat SGW vehicles, it is easy to access with Auetl… Continue Reading
Here is the Autel official guideline for FCA Secure Gateway AutoAuth. Introduction: The SGW blocks unauthorized access and manipulation of vehicle networks and vital systems. FCA says the SGW was developed not to restrict access to diagnostic data but… Continue Reading
