New Magic Motorsport Flex software update available – v7.50.0.0. Bench protocol now available for Continental SID212 and SID212EVO! From today, the RFT service is no longer required. With Flex you can now unlock and program these ECUs directly in Bench… Continue Reading
Question: There is no protocol for Ford Transit Visteon DCU-101 in Flex software. Will Flex Read Visteon Dcu 101? Is it safe to use dcu-102 protocol? Here is the clue. Yes it can do through protocol for DCU102. Ford… Continue Reading
Magic Motorsport Flex and Autotuner programmers now support the Bosch MD1CS069 ECU OBD protocol for the Iveco Daily. MMS Flex New Flex update, version 7.49.0.0, now available, implementing OBD programming for the most modern Iveco vehicles equipped with… Continue Reading
Problem: 2011 BMW X6M all keys lost. Already read the CAS3+ and saved eeprom dump. DME is an MSD85.3. Which tool will get the ISN code from DME? Autel IM608: Failed Bench failed with a Gbox2/3. Double checked sufficient… Continue Reading
Problem: It’s an Audi A8 4.2 TDI 2014 with Bosch EDC17CP44 ECU. Tried writing 3 times with Autotuner via OBD but had same error every time. This vehicle has two ECU’s. First said “Could not start transfer: 34 22”. Eventually… Continue Reading
Problem: OBDSTAR DC706 programmer is unable to connect to WiFi. Tried different networks. Attempted restarting the device. Tried using a mobile hotspot. None of these methods worked. Solution: Please check the WiFi settings. Try changing the encryption to WPA/WPA2 PSK.… Continue Reading
Get ready to tune the premium and heavy-duty lineup from South Korea! Autotuner is excited to announce support for the Bosch MD1CS012 ECU covering Hyundai, Kia, and Genesis vehicles via their Mail-in Unlock service. Great news: no ECU Opening Required!… Continue Reading
OBDSTAR released a new big TCM software update in March, 2026. OBDSTAR TCM Software V30.87 for MB FBS3 / FBS4 TCM OBD Virginization – No Risk! Now Available for Download! Supported tools: OBDSTAR X300 Classic G3 with ECU flasher activation… Continue Reading
Problem raises: A Xhorse Multi Prog programmer user noticed that his device having difficulty connecting to certain modules. The issue was puzzling because these were modules that should have been readable on bench – connecting directly to the processor pins… Continue Reading
Problem: Cloned a VW Golf 6 EDC17cp14 ECU with Magic Motorsport Flex programmer, did it on bench, written no issues. Everything went well but the car won’t start. Any help? Solution: You can’t clone 1-1 because OTP area, need transfer… Continue Reading
Problem: Tried to read BMW 6HP gearbox with CG FC200 prorammer but the device will not communicate with the TCU. Any solution? Possible solutions: 1. Direct connect with fc200 wiring. Try both with or without 120ohm between CAN L and… Continue Reading
Question: Tried to disassemble the original VAG MQB49 5C key and read key data to add a spare key using Xhorse Key Tool MIDI, the MIDI does have this option, but it says function not supported and needs VVDI Programmer… Continue Reading
It’s an Audi SQ7 2024 and it has Bosch MG1CS008 HW80 ECU. Do I need to do SFD unlock and after that Autotuner will write? Is it all OBD2 or Bench? Here is the clue. Needs a unlock. Not all… Continue Reading
Question: It is a Fiat Ducato 2023 with Delphi DCM7.1A ECU. Can I read it with Flex via obd? Fiat and PSA merged in 2021. They put PSA engine in these Ducatos. No more Marelli. The Fiat Ducato 2023… Continue Reading
Problem: Read a Ford Range SID209 with Flex programmer full obd mode. With voltage retainer LAUNCH in 14.3V. Tagging OK, registering console. patch ok. play full backup start, then stop at 44% with request to disconnect the computer. Car Won’t… Continue Reading
