These are customer solutions to Carprog full V7.28 errors “Damaged parts -6 or 4” with detailed information like “Damaged parts – ARM7 +4 ARM7(master mcu) can’t be replaced contact seller to repair your device.” Error: Damaged parts -6 Damaged… Continue Reading
New version Ksuite v2.21 clone for Ktag/Kess v2 master ecu tuning kit has been released and free download link is offered here to help you update your Kess v2 (or Ktag in future). Free Download ksuite-v2.21.zip (6,005.0K) Note: No network connection &… Continue Reading
Here is a customer solution of the easiest way to change the Mercedes Benz SD Connect C4 diagnostic system serial in the 24C02 eeprom with XPROG-M ecu programmer. It can be removed from the board or read with the chip… Continue Reading
I have read some GM models with Fgtech Galletto 4 V54 master clone ecu programmer. I want to share with you what i have discovered about Fgtech V54 so far. I put Winxp on an old laptop without anti-virus program, it goes… Continue Reading
I have had V2.13 kess v2 ecu tuning kit master clone built with firmware V4.036 for about 4 months and read & write to about 8 cars. And last week, I went to send a VW Caddy EDC16. This read fine… Continue Reading
Original Xhorse VVDI Prog ECU programmer software has newly updated to V4.4.2 (23/03/2016). Software version: V4.4.2 Firmware version: V1.2.2 Free download VVDI-PROG programmer V4.4.2 https://mega.nz/#!ylUBSIbY!Jb4Nj6mAx65xkw8WE26erW-nHJ4fr-8Dm2uLkFFkceA Password:123456 VVDI-Prog v4.4.2 updated features: * This version DON’t need update firmware + Add MC9S12A64_UNSECURED,… Continue Reading
Just done a Mercedes Benz Smart fortwo ECU remap with K-tag master ecu tuning kit. I am using Ktag 6.070 Ksuite V2.11 China clone. Firmware v6.070 is the better fw version works great with older ksuite 2.11/2.08 picture attached: www.obdii365.com
There are too many Kess v2 and K-TAG master ECU tuning clones in China market,which one should you choose? In the following parts, obdii365.com provides you three 3 ways to pick up correct one. Tips: If you need fix/repair ECU, you need Ktag. If… Continue Reading
Here’s the instruction on what to do if New Genius K-touch ecu programmer fails to detect SD card, and prompt error message as follows: “SD card not detected!! Insert the SD card and reset the hardware” Optional solutions: Option 1 Re-insert… Continue Reading
Here’s the customer solution to update Carprog full v7.28 China Clone ECU, car radios, Airbag, dashboards, immobilizers repair kit to new 8.03. AT91SAM7s256 Free download Carprog V8.03 update file: http://ulozto.net/xZtJppoy/carprog-v80-rar (PASS: 987654@2@2) http://ulozto.net/xfpwpZJN/carprog-v80-rar (PASS: 987654@2@2) (Note: customer tested our Carprog… Continue Reading
ATMEGA64 Repair Chip is the only way to update XPROG-M ecu programmer from any version to the latest V5.55. And here’s the detailed instruction to help you update xprog with ATMEGA64 chip. * Top 3 Reasons to buy this… Continue Reading
Nowadays, many people program key for VAG Audi 4th generation immobilizer system and it does no need to remove J518 computer and engine computer for the Audi A6L-2.0T before 2011 when lost all keys. Firstly, turn on the ignition switch, then… Continue Reading
Caprog full v7.28 airbag reset tool tokens run out,device not in use problem solution is provided. Problem: My Carprog full v7.28 has run out tokens and stop working. How to solve the problem? Answer: Carprog full airbag reset tool comes… Continue Reading
Recently, some New Genius K-touch & Flash Point OBDII/BOOT Protocols ECU chip tuning tool users asked for help at obd365 for the corrupted files in the TF card. And this is the solution for it and also the instruction on how to… Continue Reading
This is installation guide for New Genius K-Touch 5.005 MAP OBD2 ECU chip tuning tool by obdii365.com. This K-TOUCH installation is finished on Win 7. New Genius software free download: http://www.obd2vip.com/download/k-touch-xp-software.zip (available on WIN 7, XP) Operation system: Windows… Continue Reading
