Fgtech Galletto V54 master EU version with firmware 0475 is now available in obdii365.com. The FGTech FW0475 was based FGTech Galletto 4 FW0386,inherited most features of older version,yet,at the same time,it made some improvements to provide better and more stable… Continue Reading
I have made a Kess V2 new version of the original rework picture from Fantomel. I thought it would be good to have a update version with some more part nr. I take no credit or responsibility for this info… Continue Reading
Ksuite 2.25 is confirmed working well with Ktag firmware 7.020. This is Ktag 7.020 Ksuite 2.25 installation instruction Operating system: Windows XP Firmware: Ktag 7.020 Software: Ksuite 2.25 Free Download Ksuite 2.25 for Ktag 7.020 clone Installation… Continue Reading
Problem: My Xprog V5.84 fail to read serial eeprom, don’t give eeprom options. Error “For information, please refer to xprog-m users manual” Solution from obdii365.com engineer: Xprog v5.84 default software CD does not have eeprom capabilities which is different from previous… Continue Reading
Vehicle: Great Wall BOSH EDC16C39-6.H1 EEPROM 95320 Purpose: IMMO off Device to use: Ktag V7.020 master clone Procedure: People usually will flash Eeprom 95320 dump and connect PIN 68 and PIN 74 to turn off immo. But it is not working on this… Continue Reading
Question: Anyone tried with CG Pro 9s12 and 35160WT adapter ? Answer: I bought it just to try it… 160DOWT without Problems… 160DOWQ without Problems… Need the Adapter for WT For 35160WT, you need extra adapter and also to… Continue Reading
Vehicle: Chevrolet Cruze A J300 1.8L AT year 2012 Purpose: Flashing the engine control unit. Device used: Kess V2 v4.036 master The car arrived with errors after the service, where they changed the rear lambda, put a trick, checked… Continue Reading
Hello, Possible to read Opel Corsa with Ktag clone, the red board? I am using Ktag 7.020 for Marelli 6JO Opel Corsa. Failed to read out ECU data. It says connection error. Help please. Obdii365.com tech support: Hello, Opel Corsa… Continue Reading
How to change odometer on a Toyota Prius 2006 with eeprom 9C366 using carprog v8.21 (version now v10.93) ecu programmer. Change KM Toyota Prius 2006 93C66: Remove unit from car. Open it and find internal 93C66 EEPROM memory inside.… Continue Reading
Ksuite 2.47 software adds many working protocols comparing old version. Here’s the customer test feedback on Kess V2 EU clone version 2.47 K-suite. For sale Ksuite 2.47 that works with kess FW 5.017 Added: CATERPILLAR A5E2 P 549 VOLVO… Continue Reading
Here is the detail guide to install Fgtech Galletto 4 V54 master ecu programmer software driver on Windows XP, Windows 7, Windows 8, Windows 8.1 and Windows 10 respectively. Part 1.Operation System Requirements Part 2. Install FGTech EOBD2 Software… Continue Reading
Here’s the customer solution to help users solve the problem xprog atmega64 locked and can not read or program chip issue. This is done off board with qfp64 breakout board should be able to program onboard xprog also though. Disclaimer: Many thanks… Continue Reading
FVDI 2018 abrites commander new test report: immo off for me7.5 vag no issue. First you need to read 95040 original dump data with carprog Select EEPROM function->95XX->95040 Read and verify Save original dump: name it Immo Ori for example Then open FVDI… Continue Reading
Q: Hello anyone used this new Yanhua Mini ACDP tool for Fujitsu MB91Fxxx in Honda dash? I’ve also seen some one use UPA USB V1.4 for Fujitsu? A: You have luck with either a UPA-USB programmer or Mini ACDP, to… Continue Reading
MultiFlasher is a chip-tuning software intended for reading/writing FLASH and EEPROM memory of ECUs. It can use any adapter supporting J2534 standard, e.g. OpenPort 2.0 by Tactrix. Before flashing and after reading the program checks the firmware and checksums, and corrects them if needed. It allows… Continue Reading
