ECUHelp HTProg Download, Activate and ECU List

ECUHELP HTprog is an ECU Chip tuning Tool, a Bench Programmer, EEPROM Programmer, a Key renew tool.

 

HTProg configureation: 

HTProg KT200 Clone Adapter Only (Must use with ECUHelp KT200)

Htprog Basic Version

HTProg Adapter + Cables (Must use with ECUHelp KT200)

Htprog And Cables

HTProg Full Pack with Dongle (stand-alone)

The package comes with clone adapter, cables and encrypted dongle, it works stand alone without connecting to KT200 ECU Programmer.

Htprog Full Version

 

HTProg Function:

Chip Tuning / ECU Cloning
With HTprog you can read and write P-Flash,D-Flash, External Flash and external EEPROM with the option of automatically checksum correction, you will have many methods in most of ECUS :
1. Factory mode (On Bench for most of ECU/TCU): with this option you don’t have to open the ECU cover. Just plug some wires for power and signals and you are ready to go.

2.Tricore Boot Mode for all Tricore ECU: Opening the ECU is mandatory to connect the boot wire on the ECU board.This method is useful when the ECU is not responding

3.BDM (Background debug mode)

4.JTAG for Renesas and Freescale

BDM Read / Write
With HTprog you are able to break the protection of immobilizers like CAS in BMW. EIZ / EIS in Mercedes Benz. BCM in Volkswagen and Porsche.etc.

Built in Editors
With HTprog you can edit many Flash data like:
Edit CAS3+ VIN, ISN and keys
Edit CAS4,CAS4+ VIN,and ISN
Edit mileage for BMW instrument clusters

Other functions
You can do key reset for many brands like Audi, BMW,MIN, Porsche, Toyota,Fiat, Renault…etc.
Read/Write a wide range of SOP8 EEPROMS.
Works side by side with Autohex to make keys.

Key Features
Master version. One License for all protocols on bench.
Supports one of the largest ECU/TCU list in Cars and Trucks for ECU cloning and Chip Tuning. Supports both old and latest ECU / TCUs from Bosch,Continental, Delphi, Marelli,Denso, Tenic,TRW and Valeo.etc.
Reads all BMW long ISN from BMW DME and DDE including MD1 and MG in F/G series

IMMO BDM Read/Write
With HTprog you are able to break the protection of immobilizers like CAS in BMW, EIZ / EIS in Mercedes Benz.BCM in Volkswagen and Porsche…etc.

 

 

Download HTProg Software

 

Free download HTProg software

Current software version: 1.0.45

 

 

How to Activate HTProg Software?

To activate the HTprog clone adapter for KT200, follow the steps below:

1. Connect HTprog Clone Adapter to KT200 device, and then to the comptuer.
Like this
Connect Htprog With Kt200
2.Download the htprog software needed for the adapter

3.Install the software on your computer.

4.When the HTprog software starts, it will prompt you to enter your email address.
Connect Htprog With Kt200 1
5.Enter your email address and wait for the activation link to be sent to you.
Connect Htprog With Kt200 2
That’s it! Once you’ve activated your HTprog clone adapter for KT200, you can start using it to program your vehicles. If you have any questions or issues during the activation process, don’t hesitate to reach out to the HTprog support team for assistance.

 

 

HTProg ECU List

KT200 Clone Adapter Support List.pdf 

HTPROG Support Functions.pdf 

OBDII365