What tool to read and write Delphi DCM6.2V by OBD? Can we read other than by OBD? Here is the clue. Foxflash/KT200: VR read by OBD mode, if there is no VR file available then it cannot write it.… Continue Reading
When you are trying to program a key for newer Toyota 8A/4A (2018+) proximity all keys lost it will ask you for the 12-digit security code. How to get these codes? The newer Toyota’s have an extra security component even… Continue Reading
Problem: If the Foxflash will remove security on the Dodge 2015 and up computers if so can I tune it with HP tuners afterwards. I try to read and write Chrylser GPEC2A ecu by foxflash, it reads fine, but failed… Continue Reading
Q: Can you manage to install Drewtech j2534 Toolbox with a 3rd party J2534 device? I want to have this software for skim delete on jeeps. I’ve maanged to get the software but it would not work with my j2534… Continue Reading
iProg+ clone PORT errors are because you probably didn’t change pull-up resistor on the mainboard and 10V & 12V errors are because you probably didn’t change the resistor in ADC voltage divider on the mainboard and from what you see… Continue Reading
Some iprog+ clone are sold saying never power it up with the DC supply and not to connect it via obd2 port else it will burn. How to repair iprog clone power board if buren by 12v external power supply?… Continue Reading
Are you looking for a solution for resetting airbag crash data from cars Volvo, VAG, BMW, Mercedes and etc? Is there a universal solution or different tools/software for each cars. Can this be done via OBD or by connecting to… Continue Reading
Launch X431 X-prog3 programmer is very good at ECU/TCU cloning. Here comes an example of Mercedes Benz VGS NAG3 gearbox cloning. Device required: Launch X431 X431 PAD VII/PAD V series or IMMO series tablet (IMMO PLUS/IMMO Elite/IMMO Pro)… Continue Reading
Review: Chevrolet Corvette C7 Z06 online programming by sps2. Fault code: 2018 C7 Corvette z06 threw the P0106 code today Purpose: program the Engine Control Module K20 Purchased the SPS2 software for 2 VIN, GDS2 (not needed for… Continue Reading
Exciting news for Launch X-PROG3 users! The latest V10.80 software has made the device even more powerful, offering enhanced support for a wider range of Volkswagen/Audi IMMO and Key Programming functions, including MQB keys adding and instrument replacement. X-PROG… Continue Reading
Q: I got the CG FC200 programmer software updated to latest V1.1.3.0, but Continental TC17 and bench MPC5xx license are missing. How to activate it? A: The authorization will be activated uniformly in two days. License are free, but need… Continue Reading
What device to read and write Jaguar Land rover MEDC17.9 ECU via OBD without removing ECU? Dimsport: Yes,OBD and bench Kess v3: Yes, OBD, bench and boot Flex: Yes, OBD, bench, boot Software 3.15.0.0 adds Jaguar Land Rover Bosch… Continue Reading
Foxflash ecu programmer released new software update on May 23rd, 2023. May 23, 2023 update May can’t get any better as we release a new exclusive protocol today! In this update, you’ll find the BENCH protocol for Isuzu EDC17C83.… Continue Reading
Mazda3 and Mazda CX30 from year 2020 have S6J329CPLS Spansion mcu on Speedo. They are equipped with VISTEON cluster and have no EEPROM. Mazda 3 2020 cluster Picture from the other side of PCB. BTW, the needles does not have… Continue Reading
Here comes a similar problem: 2019 Dodge Ram DT 1500. Autel IM608 pulled pin code but would fail every time to program key. I thought it was a key issue but another tool (code cannibal) programmed no problem. I used the same… Continue Reading
