Autel Maxisys Pro MS908P program ECU SIM on BMW 750Li 2006

It’s an instruction on how to do ECU reflashing/programming/coding with Autel Maxisys Pro MS908P tablet and J2534 ECU programming device.

 

Note: so far, Autel MS908P is the only full diagnostic scanner supporting online ECU programming.

 

Model: BMW 750Li 2006

 

All operation (ready) for ecu programming:

 

Part 1 – connection issues

Step 1 – connection to voltage supply

Connect the car to a stable voltage supply

Make sure the battery clamps are properly fixed

Fully charge Autel MS908P tablet

BMW-ECU-programming-with-Autel-Maxisys-pro-1

BMW-ECU-programming-with-Autel-Maxisys-pro-2

BMW-ECU-programming-with-Autel-Maxisys-pro-3

BMW-ECU-programming-with-Autel-Maxisys-pro-4

Step 2 – connect to network

Connect Maxisys pro to the Internet

Make sure the network connection is stable to ensure a successful ECU programming

Both wired & wireless connection is ok, using ethernet cable

Check the connection status icon to confirm the internet connection is successful

BMW-ECU-programming-with-Autel-Maxisys-pro-5

BMW-ECU-programming-with-Autel-Maxisys-pro-6

BMW-ECU-programming-with-Autel-Maxisys-pro-7

BMW-ECU-programming-with-Autel-Maxisys-pro-8

BMW-ECU-programming-with-Autel-Maxisys-pro-9

Step 3 – connection to J2534 ecu programmer

Connect Maxiflash J2534 ECU programming device to MS908P using USB cable

Tighten the screws

BMW-ECU-programming-with-Autel-Maxisys-pro-10

BMW-ECU-programming-with-Autel-Maxisys-pro-11

Step 4 – connection to the car

Connect Maxisys pro ms908p to the vehicle with OBDii cable

BMW-ECU-programming-with-Autel-Maxisys-pro-12

Now, all connection complete

BMW-ECU-programming-with-Autel-Maxisys-pro-13

Part 2 – ECU programming

Here goes the ECU programming on BMW.

 

Select Diagnostics n the main menu of Maxisys pro MS908P

Select BMW

Turn ignition off…wait 10 seconds…turn ignition on

BMW-ECU-programming-with-Autel-Maxisys-pro-14

Tap OK and read out vehicle data

BMW-ECU-programming-with-Autel-Maxisys-pro-15

BMW-ECU-programming-with-Autel-Maxisys-pro-16

 

Tap CIP (coding, individualizing and programming) for ecu programming

BMW-ECU-programming-with-Autel-Maxisys-pro-17

Vehicle configuration

Read data and tap ok to go on. Edit button is available to perform customized SA configuration

BMW-ECU-programming-with-Autel-Maxisys-pro-18

Make sure and delete vehicle data correctly

BMW-ECU-programming-with-Autel-Maxisys-pro-19

Tap ok

Upon completion, tap ESC to exit

BMW-ECU-programming-with-Autel-Maxisys-pro-20

Tap yes to save revised data

Maxisys is communicating with control units for a few minutes

Confirm whether any control unit has been replaced or not before programming

Tap yes or no accordingly to continue

BMW-ECU-programming-with-Autel-Maxisys-pro-21

Select SIM for coding/programming

BMW-ECU-programming-with-Autel-Maxisys-pro-22

BMW-ECU-programming-with-Autel-Maxisys-pro-23

Tap Selective update to reprogram a specific control module separately

BMW-ECU-programming-with-Autel-Maxisys-pro-24

Or perform Complete update by selecting all modules

BMW-ECU-programming-with-Autel-Maxisys-pro-25

Here, program SIM only

Tap OK for vehicle info

BMW-ECU-programming-with-Autel-Maxisys-pro-26

Tap Execute measures plan to continue

Turn off ignition

Switch on terminal 15 (ignition)

Again, make sure of the stable network connection, and other connections to start reflashing

BMW-ECU-programming-with-Autel-Maxisys-pro-27

Coded! Stored DTCs will be cleared

BMW-ECU-programming-with-Autel-Maxisys-pro-28

Turn off ignition and remove the key with remote control from key slot (if provided).

Wait 10 seconds.

Insert the key with remote control and turn on ignition

Then go on the next action. All action will be done one by one automatically

Do not perform other tasks at the same time

BMW-ECU-programming-with-Autel-Maxisys-pro-29

BMW-ECU-programming-with-Autel-Maxisys-pro-30

 

The system will generate a report after reflashing

BMW-ECU-programming-with-Autel-Maxisys-pro-31

BMW-ECU-programming-with-Autel-Maxisys-pro-32

 

Tap End session to finish ECU reflashing/ programming

 

Reference : Autel MaxiSYS MS906 vs MaxiSYS MS908P vs Maxidas DS708

OBDII365