CG FC200 ecu programmer released new software version V1.2.9.0 on May 26th, 2025. The new version adds DTC OFF function for various BMW, Mercedes, Hyundai, VAG, PSA, Toyota, Nissan, Renault ECUs. CG FC200 new version V1.2.9.0 updating details: 1.… Continue Reading
CG FC200 ECU programmer released new software version 1.2.7.0 on April 23rd, 2025. CG FC200 V1.2.7.0 1. Added ECUs with VIN modification function: BOSCH TC2xx： MD1CP001, MG1CS003, MD1CP002, MD1CS006, MG1CP002, MG1CS080, MD1CP004 SPC5777, MD1CP004_ TC298TP, MD1CS004, MG1CS001, MG1CS002 SPC5777,… Continue Reading
What this new “Three item not ready” function in CG FC200 programmer is for? Here is the clue. Three item not ready= Three Not-Ready Monitors (three readiness monitors not ready function.) It’s to set monitors for emissions, it might be… Continue Reading
Several advanced tools support bench-mode operations for Toyota DENSO Gen3 ECUs equipped with R7F701202 or R7F701216 microprocessors, including: Dimsport Autotuner Bitbox OBDSTAR DC706 CG FC200 and more In this guide, we’ll demonstrate how to read a 2023 Toyota Sienna’s… Continue Reading
Is it possible to clone VAG Delphi DCM6.2V ECU? With which tool? For example, damaged ECU DCM6.2V with SW 04L906056LT-6430 and need to clone this one to ECU 04L906056KL-3802. HW numbers are same. What’s the easiest way to do it?… Continue Reading
CG FC200 ECU programmer released new software version V1.2.5.0 on Jan. 4th, 2025. CG FC200 new version V1.2.5.0 updating details: 1. Added the “Three readiness monitors not ready” function of GM E37\E38\E39\E39A\E78\E80\E83\E84 ECU 2. Added MELCO (Mitsubishi) series BENCH… Continue Reading
CG FC200 ECU programmer software V1.2.3.0 adds Volkswagen ECU mileage repair function for Bosch MED17.5.25, ME17.5.22, MED17.1.27 ECUs. Here is a demo guide on VW MED17.5.25 ECU mileage correction by FC200. It is a 2015 VW Sagitar with Bosch… Continue Reading
CG FC200 released a big software update on Nov. 25th, 2024. V1.2.4.0 Registered Version NEW (2024.11.25) New functions: 1. Added Paypal payment function in non-simplified Chinese version 2. Added DELPHI BOOT mode ECU: DCM6.2V MPC5674 DCM6.2A MPC5674 DCM6.2C MPC5674… Continue Reading
What tools to read GM ACDelco T87A 8 and 10 speed Transmission controller TCM? 1. OBDSTAR DC706 or G3 with ECU flasher license OBDSTAR supports following Delco E87A ECM reading/writing on bench mode. CADILLAC ACDELCO T87A SPC564A read/write CHEVROLET ACDELCO… Continue Reading
Q: Looking for a device that can do EDC17/MED17 IMMO OFF direct in software. What tool will do? Immo off is something you have to do in the lines of “code” in the eeprom or in the microprocessor. It… Continue Reading
CG FC200 ECU TCU programmer software update to V1.2.3.0 on October 19th, 2024. FC200 V1.2.3.0: 1. Added DENSO SH72531 ECUs: Nissan: 23740-5Sxxx_Gen2, 23740-3Nxxx_Gen1 Subaru: Subaru SH72531, 112800 SH72531 2. Added HONDA KEIHIN ECUs: Honda/Acura: KEIHIN 37820-xxx-xxx SH72543, KEIHIN 37820-Rxx-xxx… Continue Reading
Will OBDSTAR DC706 Clone VW Continental Simos PCR2.1 ECU? This is a frequently asked question. FC200, Launch X-prog3, Xhorse Multi Prog and many other ECU programmers can ONLY read and write PCR2.1 ECU on bench, they cannot clone this… Continue Reading
One of our customers was trying to clone the Audi A4 MED 17.1.10 TC1797 ECU using CG FC200 ECU programmer. It wrote ‘clone successful ‘ but on the vehicle it start and cuts with ‘SAFE’ on cluster on the vehicle… Continue Reading
This is a frequently asked question of CG FC200. Device is still working after the software license expires? FC200 can still be used except following functions: Functions that need to be accessed online cannot be used, including 1. BMW MSD80/81/85/87,… Continue Reading
CGDI FC200 ecu programmer released new software version V1.2.2.0 on August 4th, 2024. FC200 new version V1.2.2.0 details: 1. Added DELPHI ECUs, supporting OBD and BENCH modes: OBD/BENCH: ChinaDelphi MT34, ChinaDelphi MT80 BOOT: DCM6.2AP 2. Added DENSO ECUs: ISUZU:… Continue Reading
