Bosch MDG1 (BMW) Post-2020: Remote Unlock Now Available on AutoTuner! Things are getting serious for Bosch MDG1 ECUs fitted from 2020 onwards across BMW platforms! The DDE8 and DME8 versions, featuring the new Bosch protection, are now supported in BENCH… Continue Reading
Problem 1: Autotuner managed to brick a Delphi DCM3.5 from a Ford S max today through OBD, Was starting to write file then error comes up and the autotuner software closed itself. now left with a bricked ECU. Problem 2:… Continue Reading
Question: Trying to read Bosch MD1CS004 ECU with Flex Magicmotorsport. It provides three versions of wiring pinouts. How do I know exactly which version I have? Which one to choose from? Here is the clue. +12V power and GND are… Continue Reading
Problem: Autotuner read Peugeot 508 Delphi DCM7.1A ECU ok, but failed to OBD write. Solution: Normal, same with Flex. Just write again and it will be all OK. Need to write the file again after it fails. Put key near… Continue Reading
Question: 1). Is it possible clone vd56.1 peugeot ECU with AutoTuner programmer? 2). Anybody cloned 1:1 a continenal vd56.1 ecu with Magic MotorSport Flex boot mode? Here is the clue. The VD56.1 ecu has OTP areas so although the data… Continue Reading
AutoTuner team doesn’t stop surprising us in the last few month or so with the super updates. Autotuner now released a new exclusive update on Sep. 9th, 2025. New Exclusive AUTOTUNER Release. 09/10/2025 AT developers never sleep: Mercedes… Continue Reading
NEW EXCLUSIVE AUTOTUNER RELEASE. Autotuner is keeping the momentum going with a fresh new release for Ford and Volkswagen vehicles! The Bosch MD1CS027 ECU is now supported via OBD, exclusively with your Autotuner Tool. The normal read (NR) gives access… Continue Reading
AutoTuner released a new OBD protocol on Aug. 22nd, 2025. AT development team never rests: the OBD protocol for Bosch MD1CP006 and MG1CS036 ECUs found in Ford vehicles all years is now available. This one is for our friends across… Continue Reading
Question: It’s a 2014 Volkswagen Jetta (Simos 12.2) that needs to do Immo adaptation (ECM Swap). What tool to clone this ECU? Will OBDSTAR DC706 or FC200 do it? Or what the best way to clone this ecu without the… Continue Reading
Flex, bflash, CMD and many other tools don’t have bench protocol for the Mercedes Continental EMS71 ECU. Autotuner now released an unlock service for the MB EMS71 ECU. The Mercedes-Benz EMS71 is an Engine Control Unit (ECU) (also known… Continue Reading
New AutoTuner Release. The Bosch MED17.8.33 ECU, installed on the McLaren Artura, is now supported in BENCH mode. An exclusive support, for your AT Tool. With its sharp design, ultra-light chassis, and especially its powerful hybrid twin-turbo V6, the McLaren… Continue Reading
Here comes a similar problem: Peugeot Boxer 2012 2.2hdi SID208, Autotuner read ID ok, but won’t read on bench, won’t read via OBD too. Solution: Bench mode: On bench must use an external power supply. Try 13.8 to 14.4v.… Continue Reading
If the VAG Bosch MD1CS004 ECU manufaucered before 06/2020 (not locked), many devices could read it via the bench mode, foxflash, kt200, launch x-prog3, obdstar, FC200, Flex, KESS3 etc. Here we are talking about the MD1CS004 ECU with version HW80… Continue Reading
Both FLEX and Autotuner offer ECU unlocking services for the SID212/SID212EVO. Let’s take a look at their respective unlocking processes. SID212 & SID212 EVO on Magic MotorSport Flex Version 7.22.0.0 of Flex Out Now OBD Support for Continental/Vitesco SID212… Continue Reading
Question: Looking for a tool that can read Ford Transit SID212 ecu (SID212EVO Continental/Siemens ECU). Do you know any tool can make reading and checksum? Ford introduced a new ECU (Engine Control Unit) variant known as the SID 212. The… Continue Reading
