Free download Carprog full v9.31 software shared by a forum member and tested on BMW EEPROM M35080.. No issues. Carprog 9.31v software i used on Windows XP operating system: https://mega.nz/#!QF4D2ajZ!sew7H0E2wZeo7bfNdM3XJn4yN8i2BZGQ1u4nmR-O3dA And China Carprog clone device used together with: direct… Continue Reading
It’s a customer issue and solution to Car OBD2 ECU programmer New Genius K-touch FW v5.005 with SD card error [464] and Genius device error [465]. Device used: New Genius clone (K-Touch) ECU chip tuning tool ECU tested: Error massage: Race… Continue Reading
I need to read ECU Renault espace 21 Sagem s2000 RPTM ECU. I need a photo pinout for this ecu. I have K-tag ksuite master ecu programmer. Finally got the pinout to Ktag 6.070. Just post here to share with you… Continue Reading
Here is the customer solution to UPA USB V1.3 programmer “usb device not recognized” problem. Problem: Does someone has dump for 24lc128 eeprom v1.3r2? My UUSP upa was working fine, and today it say’s usb device not recognized, I try with… Continue Reading
Carprog full China clone Airbag reset, Odometer, Radio, Mileage, Dashboard, Immobilizer, Transponder programmer V7.28 software can be downloaded free here. Software version: V7.28 Operating system: Windows XP (without anti-virus) Carprog full v7.28 clone software free download http://www.obd2vip.com/download/carprog%207.28.zip Software… Continue Reading
Good news! Engineers at obdii365.com has developed Ksuite 2.22 and tested it on Kess v2 firmware v4.036 already. Ktag will be tested with it in the near future. Here is the instruction on how to install Ksuite 2.22 and test… Continue Reading
These are customer solutions to Carprog full V7.28 errors “Damaged parts -6 or 4” with detailed information like “Damaged parts – ARM7 +4 ARM7(master mcu) can’t be replaced contact seller to repair your device.” Error: Damaged parts -6 Damaged… Continue Reading
New version Ksuite v2.21 clone for Ktag/Kess v2 master ecu tuning kit has been released and free download link is offered here to help you update your Kess v2 (or Ktag in future). Free Download ksuite-v2.21.zip (6,005.0K) Note: No network connection &… Continue Reading
Here is a customer solution of the easiest way to change the Mercedes Benz SD Connect C4 diagnostic system serial in the 24C02 eeprom with XPROG-M ecu programmer. It can be removed from the board or read with the chip… Continue Reading
I have read some GM models with Fgtech Galletto 4 V54 master clone ecu programmer. I want to share with you what i have discovered about Fgtech V54 so far. I put Winxp on an old laptop without anti-virus program, it goes… Continue Reading
I have had V2.13 kess v2 ecu tuning kit master clone built with firmware V4.036 for about 4 months and read & write to about 8 cars. And last week, I went to send a VW Caddy EDC16. This read fine… Continue Reading
Original Xhorse VVDI Prog ECU programmer software has newly updated to V4.4.2 (23/03/2016). Software version: V4.4.2 Firmware version: V1.2.2 Free download VVDI-PROG programmer V4.4.2 https://mega.nz/#!ylUBSIbY!Jb4Nj6mAx65xkw8WE26erW-nHJ4fr-8Dm2uLkFFkceA Password:123456 VVDI-Prog v4.4.2 updated features: * This version DON’t need update firmware + Add MC9S12A64_UNSECURED,… Continue Reading
Just done a Mercedes Benz Smart fortwo ECU remap with K-tag master ecu tuning kit. I am using Ktag 6.070 Ksuite V2.11 China clone. Firmware v6.070 is the better fw version works great with older ksuite 2.11/2.08 picture attached: www.obdii365.com
There are too many Kess v2 and K-TAG master ECU tuning clones in China market,which one should you choose? In the following parts, obdii365.com provides you three 3 ways to pick up correct one. Tips: If you need fix/repair ECU, you need Ktag. If… Continue Reading
Here’s the instruction on what to do if New Genius K-touch ecu programmer fails to detect SD card, and prompt error message as follows: “SD card not detected!! Insert the SD card and reset the hardware” Optional solutions: Option 1 Re-insert… Continue Reading
