This is a Chrysler GPEC2A ECU and one of our customers got the “ERROR WAKE” when reading this ECU using the new KT200 (the same as Foxflash). Possible reason: 1. Incorrect wiring connection 2. Voltage issue. Solution: Connect… Continue Reading
There are some tools to read and write GM/Geely Delphi MT80/MT80.1 ECU. Delphi MT80 ECU usually has problems car not start, No fuel injection signals, No ignition signals, it’s a common problem can be repaired with ecu tools. The problem… Continue Reading
There are some tools that could read and write Mercedes Delphi CRD3PLUS A0 ecu. Kess V2: OBD Tested crd3 plus with clone kess v2 5.017, read/write OK To read a Mercedes CRD3Plus ecu via obd, be prepared for it… Continue Reading
Some people experiencing the same problem with their foxflash tool. It worked fine but suddenly wouldn’t start. Open FoxFlash Manager and then click Activate, nothing happens. Change another PC still no luck. If your Foxflash only shows USB serial… Continue Reading
Very often we can see complaints of users to full Read/Write on Denso units via BDM pads or a rainbow cable. After several hours = here you are the solution. The problem is in the electromagnetic interference on these low… Continue Reading
What tool to read and write Delphi DCM6.2V by OBD? Can we read other than by OBD? Here is the clue. Foxflash/KT200: VR read by OBD mode, if there is no VR file available then it cannot write it.… Continue Reading
Some people reported that their Foxflash software does not start after software update or change to a new laptop. Only FoxFlash manager is working. Error” execute download with dfbtech contact support” Here is the clue. Same solution to new KT200… Continue Reading
ECUHELP HTprog is an ECU Chip tuning Tool, a Bench Programmer, EEPROM Programmer, a Key renew tool. HTProg configureation: HTProg KT200 Clone Adapter Only (Must use with ECUHelp KT200) HTProg Adapter + Cables (Must use with ECUHelp KT200) HTProg… Continue Reading
Foxflash/kt200 programmers can read and write this sid807evo of psa as well as Ford and Volvo. OBD: SID807EVO confirmed working by obd. Here’s some feedback: Ford c max sid807evo Read and Write via obd ok, Dtc off FORD 2011… Continue Reading
How to unlock FCA Chrysler Jeep continental 2015+ GPEG2A ECU to use hptuner for tuning? What tool is used? Here’s the clue. Hptuner: No Original hptuners also can’t unlock gpec2a, need send ecu for unlock. So does the… Continue Reading
Foxflash/KT200 will read, write and clone PSA MEV17.4.2 in both Bench and boot mode. It will do auto checksum. Foxflash MEV17.4.2 bench pinout To read and write use the following driver: → BENCH TRICORE → CITROEN / PEUGEOT → TC1767… Continue Reading
KT200 programmer Full backup Motorola NCG4 Dodge Journey 2.7 automatic by BDM/JTAG. Pre-scheduling backup, only 10 minutes. I need to do dtc off and a little more power. I know that just changing the vin and pairing with the immobilizer… Continue Reading
How-to: read and write VAG VW Audi Skoda Seat Bosch MED17.1.1 TC1796/TC1797 on bench and boot mode using KT200/Foxflash ecu programmers. Bench Mode: BOSCH MED17.1.1 [ 1796 protocol] Connect the multifunction cable as follows: To read and write use… Continue Reading
Some pcm users may have problem reading VW Audi ecu med17.5.5 with bench module 71 (error image attached below). It gives error unsupported trot version. How to fix it? Solution: You cannot do this ECU – it has new protection.… Continue Reading
ECUHelp KT200 online and offline software was released to V2023.01 on Jan. 2023. What’s new in 2023.01 version? 1. Fixed the bug that the software functions were not synchronised. 2. Optimised server connection time, high speed and convenience. 3. Fixed the… Continue Reading
